Acetal - ABS - Nylon - Nylatron - Ertalyte - Polycarbonate - LEXAN - MARLON - ARLA PC - Polyethylene - Tufnol - PEEK - PAI PEI - PI - PPS PSU - PTFe - PVDF - Acrylic - Perspex - REPSOL GLASS - petg - VERALITE - polypropylene - pvC
Engineering and design plastics Ltd, 84 High Street, Cherry Hinton, Cambridge, Cambridgeshire, CB1 9HZ, UK.

  Home Contact us Services Products

Extruded NYLON 6 [ERTALON® 6SA] & NYLON 6.6 [ERTALON® 66SA]

 

PROPERTIES

APPLICATIONS
  • HIGH MECHANICAL STRENGTH, STIFFNESS, HARDNESS AND TOUGHNESS
  • GOOD FATIGUE RESISTANCE
  • HIGH MECHCANICAL DAMPING ABILITY
  • GOOD SLIDING PROPERTIES
  • EXCELLENT WEAR RESITANCE
  • SUITABLE FOR FOOD CONTACT (NYLON 6.6 ONLY)
 
  • SLEEVES
  • SLIDE BEARINGS
  • WEAR PADS / STRIPS
  • SUPPORT WHEELS
  • CONVEYOR ROLLERS
  • TENSION ROLLERS
  • PULLEYS/PULLEY-LININGS
  • HAMMER HEADS
  • SCRAPERS
  • GEAR WHEELS
  • SPROCKETS
  • SEAL-RINGS
  • FEED SCREWS
  • STAR WHEELS
  • CUTTING BOARDS
  • INSULATORS
  • CAMS
  • BUFFER BLOCKS
   

Quadrant EPP brand their Nylon products ERTALON®

NYLON 6 (ERTALON® 6SA) EXTRUDED Natural

This material offers an optimal combination of mechanical strength, stiffness, toughness, mechanical damping properties and wear resistance. These properties, together with a favourable electrical insulating ability, and good chemical resistance make Nylon 6 a "general purpose" grade for mechanical construction and maintenance applications.

ERTALON 6 SA Material data sheet ERTALON 6 SA safety data sheet

Availability
  • Rod extruded Æ 5mm to 320mm
  • Tube ext. 20mm O/Dx10mm I/D to 100mm O/D to 60mm I/D
  • Thin sheet extruded 1mm to 6mm
  • Plate extruded 8mm to 100mm

NYLON 6 (ERTALON® 6SA) EXTRUDED Black

Due to the addition of a pigment only, the material is black in colour, which is preferred by some users in certain applications.

ERTALON 6 SA Material data sheet ERTALON 6 SA safety data sheet

Availability
  • Rod extruded Æ 10mm to 200mm
  • Tube extruded 20mm O/D x 10mm I/D to 50mm O/D to 30mm I/D
  • Plate extruded 8mm to 50mm

NYLON 66 (ERTALON® 66SA) EXTRUDED Natural

Has a higher mechanical strength, stiffness and creep resistance as well as a better resistance to temperature and wear than nylon 6. On the other hand, its impact strength and mechanical damping ability are poorer. Recommended for use on automatic lathes.

ERTALON 66 SA Material data sheet ERTALON 66 SA safety data sheet

Availability
  • Rod extruded Æ 5mm to 250mm
  • Rod Precision ground on request
  • Tube extruded 20mm O/D x 10mm I/D to 100mm O/D to 80mm I/D
  • Thin sheet extruded 2mm to 6mm
  • Plate extruded 8mm to 60mm
  • Machined plate 1.59mm to 50mm
  • Coiled strip 0.25mm to 3.18mm

NYLON 66 (ERTALON® 66SA) EXTRUDED Black

Due to the addition of a pigment only, the material is black in colour, which is preferred by some users in certain applications.

ERTALON 66 SA Material data sheet ERTALON 66 SA safety data sheet

Availability
  • Rod extruded Æ 16mm to 60mm
  • Rod Precision ground on request

NYLON 66 30% GLASS FILLED (ERTALON® 66-GF30) EXTRUDED Black

Compared with virgin nylon 66, this 30% glass fibre reinforced nylon grade offers increased strength, stiffness, creep resistance and dimensional stability whilst retaining an excellent wear resistance. It also allows higher max. service temperatures.

ERTALON 66-GF30 Material data sheet ERTALON 66-GF30 Safety data sheet

Availability
  • Rod extruded Æ 10mm to 200mm
  • Plate extruded 10mm to 100mm

Ertalon® is a registered trade mark of Quadrant Engineering Plastic Products

The information given here is believed to be correct, but completeness and accuracy are not guaranteed. The user shall be fully responsible for determining the suitability of products for the intended use.